Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5976 visitantes online.
Productos
Información
Destacado
Inicio >> JBL >> GTO601.1 Manual de Usuario
 
 0 artículo(s) en Su carrito 

JBL GTO601.1
Manual de Usuario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del JBL GTO601.1 Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como archivo PDF después de que lo compre.

El Manual del Propietario (a veces llamado Manual del Usuario o Guía del Usuario) contiene información sobre cómo utilizar su dispositivo. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
INSTALLATION AND SETUP
SETTING THE CROSSOVER(S) Determine your system plans and set the crossover mode switch accordingly. If you plan to use the GTO75.2 or GTO75.4 to drive full-range speakers, set the crossover mode to FLAT and skip to �Setting Input Sensitivity.� Initially set the crossover frequency control midway. While listening to music, adjust the crossover for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible. Systems using a separate subwoofer set the crossover mode to HP (high pass) for your full-range speakers. Adjust the crossover frequency to limit bass and provide increased system volume with less distortion. For subwoofers, choose the highest frequency that removes vocal information from the sound of the subwoofer. If using the GTO75.2 or GTO75.4 to drive a subwoofer(s), set the crossover mode to LP (low pass). NOTE: The GTO301.1, GTO601.1, GTO1201.1 and the subwoofer output of the GTO755.6 are low-pass only and do not have a crossover mode switch. Figure 12. Control end panel. SETTING INPUT SENSITIVITY 1. Initially turn the INPUT LEVEL control(s) to minimum (counter clockwise). 2. Reconnect the (�) negative lead to the vehicle�s battery. Apply power to the audio system and play a dynamic music track. 3. On the source unit, increase the volume control to 3/4 volume. Slowly increase the INPUT LEVEL control(s) toward three o�clock until you hear slight distortion in the music. Then reduce the INPUT LEVEL slightly until distortion is no longer heard. NOTE: After the source unit is on, red LEDs (on the top panel) will light, indicating the amplifier is on. If not, check the wiring, especially the remote connection from the source unit. Also refer to �Troubleshooting� on the next page. REMOTE LEVEL CONTROL The GTO755.6 and all three GTO subwoofer amplifiers have inputs for an optional remote level control (RLC). This will allow the amplifier�s input level to be adjusted from the listening position. Connect the optional remote level control using the RJ-11 jack on the side of the amplifier. Install the control module in the front of the vehicle within easy reach of the driver. Under the dash or in the center console are both suitable locations. SETTING THE BASS BOOST The GTO755.6, GTO301.1, GTO601.1 and GTO1201.1 are all equipped with a bassboost control. This allows you to adjust the bass output of your system at 50Hz up to 12dB and enhance low frequency. AUX OUTPUT GTO amplifiers (except GTO755.6) are equipped with full-range outputs that can be used to connect additional amplifiers. NOTE: When using the high-level inputs, the AUX outputs can be used to pass a line-level signal to another amplifier. INSTALLING NEON TUBES (OPTIONAL) 1. Using a Phillips screwdriver, remove all screws on the amplifier�s output/power end panel and set them aside. 2. Using a 3 �32-inch Allen wrench, remove only the screws on the amplifier�s (top) clear cover and set them aside. 3. Remove the end panel and slide the cover off. Set both parts aside. 4. Locate the enclosed hardware bag and remove the four clips. Each clip has a square end and a larger round end. Using a round end, press two clips onto each neon tube (e.g., Street Glow AN9 or equivalent), as shown in Figure 13. 5. For each tube, align both clips so the square ends slide onto an exposed extrusion edge, as shown in Figure 9. Do not cover any screw holes. When installed correctly, each neon tube will sit under an extrusion and not be visible when viewed from directly above. 6. Route each neon tube�s power cable through its respective NEON hole on the end panel (see Figure 13). 7. Slide the cover back into place and reinstall its screws. Then, replace the end panel and reinstall its screws. 8. Finish the installation of the neon tubes as instructed in their owner�s manual.

GTO75.2

GTO75.4

GTOB300.1/600.1/1200.1

GTO75.6
6

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.167 - Number of Queries: 125 - Query Time: 0.044