Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5811 visitantes online.
Productos
Información
Destacado
Inicio >> JBL >> DA1002 Manual de Usuario
 
 0 artículo(s) en Su carrito 

JBL DA1002
Manual de Usuario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del JBL DA1002 Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como archivo PDF después de que lo compre.

El Manual del Propietario (a veces llamado Manual del Usuario o Guía del Usuario) contiene información sobre cómo utilizar su dispositivo. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
Observe the following color-codes: Left+: White Left�: White with black stripe Right+: Gray Right�: Gray with black stripe 4. If you are connecting your Decade Series amplifier to a source unit with output voltage higher than 4V, connect the output signal wires of the source unit to the floating ground factory head unit inputs. Because the inputs have an impedance of 100K ohms, this connection will provide the best noise-free performance possible.

Setting Input Sensitivity Proper input sensitivity control settings on Decade Series power amplifiers are critical to ensure optimum performance, low noise levels and maximum system reliability. As a general rule, controls at the front end of a system (source, equalizers and other processors) should be set as high as possible with the amplifier input sensitivity set as low as possible while still providing adequate volume levels. Using a high signal level and a low sensitivity setting will help keep background noise in the system to a minimum.

System Setup and Adjustment
Electronic Crossover The electronic crossover(s) in your Decade Series amplifier can be selected as a 12dB/oct. high-pass filter at 120Hz (HPF), a 12dB/oct. low-pass filter at 80Hz (LPF) or it can be defeated (FLAT).

Initially, turn the input sensitivity GAIN control to its minimum (counter-clockwise) position. 1. Reconnect the (�) negative lead to your vehicle�s battery. Apply power to the audio system and play a favorite music track from a CD or tape. (Note: After the source unit is on, the JBL badge (on the top panel) will illuminate, indicating the amplifier is on. If not, check the wiring, especially the remote connection from the source unit. Also refer to �Troubleshooting� on page 7.) 2. On the source unit, increase the volume control until it is approximately 3/4 of its maximum output level. Slowly increase the Input Sensitivity control (clockwise) toward three o� clock and, at the same time, listen to the quality of the reproduced sound.

At some point, you�ll hear distortion on the music peaks. Stop the adjustment and turn it back slightly. This is the maximum undistorted output level of your system, and should not be exceeded during use. 3. After adjusting the level of the main speakers in your system, you should adjust the remaining channels (if you are using a DA3504 or a multi-amp system) for the desired system balance. You�ll find this easiest to do by adjusting the channels in the following order: 1) front speakers, 2) rear speakers, 3) subwoofer. Elaborate, multichannel systems may be too complex to adjust. Your local JBL installation specialist is the best person to help with such adjustments.

5

Quizás también quiera comprar

$4.99

DA1002 JBL
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.157 - Number of Queries: 101 - Query Time: 0.045